7.4.23 IOCON_PIO0_8
Table 79. IOCON_PIO0_8 register (IOCON_PIO0_8, address 0x4004 4060)
bit description
Bit Symbol Value Description Reset value
2:0 FUNC Selects pin function. All other values are reserved. 000
0x0 Selects function PIO0_8.
0x1 Selects function MISO0.
0x2 Selects function CT16B0_MAT0.
4:3 MODE Selects function mode (on-chip pull-up/pull-down resistor control). 10
0x0 Inactive (no pull-down/pull-up resistor enabled).
0x1 Pull-down resistor enabled.
0x2 Pull-up resistor enabled.
0x3 Repeater mode.
5 HYS Hysteresis.
0 Disable.
1 Enable.
* LPC11xx.h V1.10 24 November 2010
* CMSIS Cortex-M0 Core Peripheral Access Layer Header File for LPC11xx
/*------------- System Control (SYSCON) --------------------------------------*/
typedef struct
{
__IO uint32_t SYSMEMREMAP; /*!< Offset: 0x000 (R/W) System memory remap Register */
__IO uint32_t PRESETCTRL; /*!< Offset: 0x004 (R/W) Peripheral reset control Register */
__IO uint32_t SYSPLLCTRL; /*!< Offset: 0x008 (R/W) System PLL control Register */
__I uint32_t SYSPLLSTAT; /*!< Offset: 0x00C (R/ ) System PLL status Register */
uint32_t RESERVED0[4];
__IO uint32_t SYSOSCCTRL; /*!< Offset: 0x020 (R/W) System oscillator control Register */
__IO uint32_t WDTOSCCTRL; /*!< Offset: 0x024 (R/W) Watchdog oscillator control Register */
__IO uint32_t IRCCTRL; /*!< Offset: 0x028 (R/W) IRC control Register */
uint32_t RESERVED1[1];
__I uint32_t SYSRSTSTAT; /*!< Offset: 0x030 (R/ ) System reset status Register */
uint32_t RESERVED2[3];
__IO uint32_t SYSPLLCLKSEL; /*!< Offset: 0x040 (R/W) System PLL clock source select Register */
__IO uint32_t SYSPLLCLKUEN; /*!< Offset: 0x044 (R/W) System PLL clock source update enable Register */
uint32_t RESERVED3[10];
__IO uint32_t MAINCLKSEL; /*!< Offset: 0x070 (R/W) Main clock source select Register */
__IO uint32_t MAINCLKUEN; /*!< Offset: 0x074 (R/W) Main clock source update enable Register */
__IO uint32_t SYSAHBCLKDIV; /*!< Offset: 0x078 (R/W) System AHB clock divider Register */
uint32_t RESERVED4[1];
__IO uint32_t SYSAHBCLKCTRL; /*!< Offset: 0x080 (R/W) System AHB clock control Register */
uint32_t RESERVED5[4];
__IO uint32_t SSP0CLKDIV; /*!< Offset: 0x094 (R/W) SSP0 clock divider Register */
__IO uint32_t UARTCLKDIV; /*!< Offset: 0x098 (R/W) UART clock divider Register */
__IO uint32_t SSP1CLKDIV; /*!< Offset: 0x09C (R/W) SSP1 clock divider Register */
uint32_t RESERVED6[1];
uint32_t RESERVED7[11];
__IO uint32_t WDTCLKSEL; /*!< Offset: 0x0D0 (R/W) WDT clock source select Register */
__IO uint32_t WDTCLKUEN; /*!< Offset: 0x0D4 (R/W) WDT clock source update enable Register */
__IO uint32_t WDTCLKDIV; /*!< Offset: 0x0D8 (R/W) WDT clock divider Register */
uint32_t RESERVED9[1];
__IO uint32_t CLKOUTCLKSEL; /*!< Offset: 0x0E0 (R/W) CLKOUT clock source select Register */
__IO uint32_t CLKOUTUEN; /*!< Offset: 0x0E4 (R/W) CLKOUT clock source update enable Register */
__IO uint32_t CLKOUTDIV; /*!< Offset: 0x0E8 (R/W) CLKOUT clock divider Register */
uint32_t RESERVED10[5];
__I uint32_t PIOPORCAP0; /*!< Offset: 0x100 (R/ ) POR captured PIO status 0 Register */
__I uint32_t PIOPORCAP1; /*!< Offset: 0x104 (R/ ) POR captured PIO status 1 Register */
uint32_t RESERVED11[11];
uint32_t RESERVED12[7];
__IO uint32_t BODCTRL; /*!< Offset: 0x150 (R/W) BOD control Register */
__IO uint32_t SYSTCKCAL; /*!< Offset: 0x154 (R/W) System tick counter calibration Register */
uint32_t RESERVED13[1];
uint32_t RESERVED14[5];
uint32_t RESERVED15[2];
uint32_t RESERVED16[34];
__IO uint32_t STARTAPRP0; /*!< Offset: 0x200 (R/W) Start logic edge control Register 0 */
__IO uint32_t STARTERP0; /*!< Offset: 0x204 (R/W) Start logic signal enable Register 0 */
__O uint32_t STARTRSRP0CLR; /*!< Offset: 0x208 ( /W) Start logic reset Register 0 */
__I uint32_t STARTSRP0; /*!< Offset: 0x20C (R/ ) Start logic status Register 0 */
__IO uint32_t STARTAPRP1; /*!< Offset: 0x210 (R/W) Start logic edge control Register 1 (LPC11UXX only) */
__IO uint32_t STARTERP1; /*!< Offset: 0x214 (R/W) Start logic signal enable Register 1 (LPC11UXX only) */
__O uint32_t STARTRSRP1CLR; /*!< Offset: 0x218 ( /W) Start logic reset Register 1 (LPC11UXX only) */
__I uint32_t STARTSRP1; /*!< Offset: 0x21C (R/ ) Start logic status Register 1 (LPC11UXX only) */
uint32_t RESERVED17[4];
__IO uint32_t PDSLEEPCFG; /*!< Offset: 0x230 (R/W) Power-down states in Deep-sleep mode Register */
__IO uint32_t PDAWAKECFG; /*!< Offset: 0x234 (R/W) Power-down states after wake-up from Deep-sleep mode Register*/
__IO uint32_t PDRUNCFG; /*!< Offset: 0x238 (R/W) Power-down configuration Register*/
uint32_t RESERVED18[110];
__I uint32_t DEVICE_ID; /*!< Offset: 0x3F4 (R/ ) Device ID Register */
} LPC_SYSCON_TypeDef;
/*------------- Pin Connect Block (IOCON) --------------------------------*/
typedef struct
{
__IO uint32_t PIO2_6; /*!< Offset: 0x000 (R/W) I/O configuration for pin PIO2_6 */
uint32_t RESERVED0[1];
__IO uint32_t PIO2_0; /*!< Offset: 0x008 (R/W) I/O configuration for pin PIO2_0/DTR/SSEL1 */
__IO uint32_t RESET_PIO0_0; /*!< Offset: 0x00C (R/W) I/O configuration for pin RESET/PIO0_0 */
__IO uint32_t PIO0_1; /*!< Offset: 0x010 (R/W) I/O configuration for pin PIO0_1/CLKOUT/CT32B0_MAT2 */
__IO uint32_t PIO1_8; /*!< Offset: 0x014 (R/W) I/O configuration for pin PIO1_8/CT16B1_CAP0 */
uint32_t RESERVED1[1];
__IO uint32_t PIO0_2; /*!< Offset: 0x01C (R/W) I/O configuration for pin PIO0_2/SSEL0/CT16B0_CAP0 */
__IO uint32_t PIO2_7; /*!< Offset: 0x020 (R/W) I/O configuration for pin PIO2_7 */
__IO uint32_t PIO2_8; /*!< Offset: 0x024 (R/W) I/O configuration for pin PIO2_8 */
__IO uint32_t PIO2_1; /*!< Offset: 0x028 (R/W) I/O configuration for pin PIO2_1/nDSR/SCK1 */
__IO uint32_t PIO0_3; /*!< Offset: 0x02C (R/W) I/O configuration for pin PIO0_3 */
__IO uint32_t PIO0_4; /*!< Offset: 0x030 (R/W) I/O configuration for pin PIO0_4/SCL */
__IO uint32_t PIO0_5; /*!< Offset: 0x034 (R/W) I/O configuration for pin PIO0_5/SDA */
__IO uint32_t PIO1_9; /*!< Offset: 0x038 (R/W) I/O configuration for pin PIO1_9/CT16B1_MAT0 */
__IO uint32_t PIO3_4; /*!< Offset: 0x03C (R/W) I/O configuration for pin PIO3_4 */
__IO uint32_t PIO2_4; /*!< Offset: 0x040 (R/W) I/O configuration for pin PIO2_4 */
__IO uint32_t PIO2_5; /*!< Offset: 0x044 (R/W) I/O configuration for pin PIO2_5 */
__IO uint32_t PIO3_5; /*!< Offset: 0x048 (R/W) I/O configuration for pin PIO3_5 */
__IO uint32_t PIO0_6; /*!< Offset: 0x04C (R/W) I/O configuration for pin PIO0_6/SCK0 */
__IO uint32_t PIO0_7; /*!< Offset: 0x050 (R/W) I/O configuration for pin PIO0_7/nCTS */
__IO uint32_t PIO2_9; /*!< Offset: 0x054 (R/W) I/O configuration for pin PIO2_9 */
__IO uint32_t PIO2_10; /*!< Offset: 0x058 (R/W) I/O configuration for pin PIO2_10 */
__IO uint32_t PIO2_2; /*!< Offset: 0x05C (R/W) I/O configuration for pin PIO2_2/DCD/MISO1 */
__IO uint32_t PIO0_8; /*!< Offset: 0x060 (R/W) I/O configuration for pin PIO0_8/MISO0/CT16B0_MAT0 */
__IO uint32_t PIO0_9; /*!< Offset: 0x064 (R/W) I/O configuration for pin PIO0_9/MOSI0/CT16B0_MAT1 */
__IO uint32_t SWCLK_PIO0_10; /*!< Offset: 0x068 (R/W) I/O configuration for pin SWCLK/PIO0_10/SCK0/CT16B0_MAT2 */
__IO uint32_t PIO1_10; /*!< Offset: 0x06C (R/W) I/O configuration for pin PIO1_10/AD6/CT16B1_MAT1 */
__IO uint32_t PIO2_11; /*!< Offset: 0x070 (R/W) I/O configuration for pin PIO2_11/SCK0 */
__IO uint32_t R_PIO0_11; /*!< Offset: 0x074 (R/W) I/O configuration for pin TDI/PIO0_11/AD0/CT32B0_MAT3 */
__IO uint32_t R_PIO1_0; /*!< Offset: 0x078 (R/W) I/O configuration for pin TMS/PIO1_0/AD1/CT32B1_CAP0 */
__IO uint32_t R_PIO1_1; /*!< Offset: 0x07C (R/W) I/O configuration for pin TDO/PIO1_1/AD2/CT32B1_MAT0 */
__IO uint32_t R_PIO1_2; /*!< Offset: 0x080 (R/W) I/O configuration for pin nTRST/PIO1_2/AD3/CT32B1_MAT1 */
__IO uint32_t PIO3_0; /*!< Offset: 0x084 (R/W) I/O configuration for pin PIO3_0/nDTR */
__IO uint32_t PIO3_1; /*!< Offset: 0x088 (R/W) I/O configuration for pin PIO3_1/nDSR */
__IO uint32_t PIO2_3; /*!< Offset: 0x08C (R/W) I/O configuration for pin PIO2_3/RI/MOSI1 */
__IO uint32_t SWDIO_PIO1_3; /*!< Offset: 0x090 (R/W) I/O configuration for pin SWDIO/PIO1_3/AD4/CT32B1_MAT2 */
__IO uint32_t PIO1_4; /*!< Offset: 0x094 (R/W) I/O configuration for pin PIO1_4/AD5/CT32B1_MAT3 */
__IO uint32_t PIO1_11; /*!< Offset: 0x098 (R/W) I/O configuration for pin PIO1_11/AD7 */
__IO uint32_t PIO3_2; /*!< Offset: 0x09C (R/W) I/O configuration for pin PIO3_2/nDCD */
__IO uint32_t PIO1_5; /*!< Offset: 0x0A0 (R/W) I/O configuration for pin PIO1_5/nRTS/CT32B0_CAP0 */
__IO uint32_t PIO1_6; /*!< Offset: 0x0A4 (R/W) I/O configuration for pin PIO1_6/RXD/CT32B0_MAT0 */
__IO uint32_t PIO1_7; /*!< Offset: 0x0A8 (R/W) I/O configuration for pin PIO1_7/TXD/CT32B0_MAT1 */
__IO uint32_t PIO3_3; /*!< Offset: 0x0AC (R/W) I/O configuration for pin PIO3_3/nRI */
__IO uint32_t SCK_LOC; /*!< Offset: 0x0B0 (R/W) SCK pin location select Register */
__IO uint32_t DSR_LOC; /*!< Offset: 0x0B4 (R/W) DSR pin location select Register */
__IO uint32_t DCD_LOC; /*!< Offset: 0x0B8 (R/W) DCD pin location select Register */
__IO uint32_t RI_LOC; /*!< Offset: 0x0BC (R/W) RI pin location Register */
} LPC_IOCON_TypeDef;
/*------------- General Purpose Input/Output (GPIO) --------------------------*/
typedef struct
{
union {
__IO uint32_t MASKED_ACCESS[4096]; /*!< Offset: 0x0000 (R/W) Port data Register for pins PIOn_0 to PIOn_11 */
struct {
uint32_t RESERVED0[4095];
__IO uint32_t DATA; /*!< Offset: 0x3FFC (R/W) Port data Register */
};
};
uint32_t RESERVED1[4096];
__IO uint32_t DIR; /*!< Offset: 0x8000 (R/W) Data direction Register */
__IO uint32_t IS; /*!< Offset: 0x8004 (R/W) Interrupt sense Register */
__IO uint32_t IBE; /*!< Offset: 0x8008 (R/W) Interrupt both edges Register */
__IO uint32_t IEV; /*!< Offset: 0x800C (R/W) Interrupt event Register */
__IO uint32_t IE; /*!< Offset: 0x8010 (R/W) Interrupt mask Register */
__I uint32_t RIS; /*!< Offset: 0x8014 (R/ ) Raw interrupt status Register */
__I uint32_t MIS; /*!< Offset: 0x8018 (R/ ) Masked interrupt status Register */
__O uint32_t IC; /*!< Offset: 0x801C ( /W) Interrupt clear Register */
} LPC_GPIO_TypeDef;
/*------------- Timer (TMR) --------------------------------------------------*/
typedef struct
{
__IO uint32_t IR; /*!< Offset: 0x000 (R/W) Interrupt Register */
__IO uint32_t TCR; /*!< Offset: 0x004 (R/W) Timer Control Register */
__IO uint32_t TC; /*!< Offset: 0x008 (R/W) Timer Counter Register */
__IO uint32_t PR; /*!< Offset: 0x00C (R/W) Prescale Register */
__IO uint32_t PC; /*!< Offset: 0x010 (R/W) Prescale Counter Register */
__IO uint32_t MCR; /*!< Offset: 0x014 (R/W) Match Control Register */
__IO uint32_t MR0; /*!< Offset: 0x018 (R/W) Match Register 0 */
__IO uint32_t MR1; /*!< Offset: 0x01C (R/W) Match Register 1 */
__IO uint32_t MR2; /*!< Offset: 0x020 (R/W) Match Register 2 */
__IO uint32_t MR3; /*!< Offset: 0x024 (R/W) Match Register 3 */
__IO uint32_t CCR; /*!< Offset: 0x028 (R/W) Capture Control Register */
__I uint32_t CR0; /*!< Offset: 0x02C (R/ ) Capture Register 0 */
uint32_t RESERVED1[3];
__IO uint32_t EMR; /*!< Offset: 0x03C (R/W) External Match Register */
uint32_t RESERVED2[12];
__IO uint32_t CTCR; /*!< Offset: 0x070 (R/W) Count Control Register */
__IO uint32_t PWMC; /*!< Offset: 0x074 (R/W) PWM Control Register */
} LPC_TMR_TypeDef;
/******************************************************************************/
/* Peripheral memory map */
/******************************************************************************/
/* Base addresses */
#define LPC_FLASH_BASE (0x00000000UL)
#define LPC_RAM_BASE (0x10000000UL)
#define LPC_APB0_BASE (0x40000000UL)
#define LPC_AHB_BASE (0x50000000UL)
/* APB0 peripherals */
#define LPC_CT16B0_BASE (LPC_APB0_BASE + 0x0C000)
#define LPC_CT16B1_BASE (LPC_APB0_BASE + 0x10000)
#define LPC_CT32B0_BASE (LPC_APB0_BASE + 0x14000)
#define LPC_CT32B1_BASE (LPC_APB0_BASE + 0x18000)
#define LPC_IOCON_BASE (LPC_APB0_BASE + 0x44000)
#define LPC_SYSCON_BASE (LPC_APB0_BASE + 0x48000)
/* AHB peripherals */
#define LPC_GPIO_BASE (LPC_AHB_BASE + 0x00000)
#define LPC_GPIO0_BASE (LPC_AHB_BASE + 0x00000)
#define LPC_GPIO1_BASE (LPC_AHB_BASE + 0x10000)
#define LPC_GPIO2_BASE (LPC_AHB_BASE + 0x20000)
#define LPC_GPIO3_BASE (LPC_AHB_BASE + 0x30000)
/******************************************************************************/
/* Peripheral declaration */
/******************************************************************************/
#define LPC_TMR16B0 ((LPC_TMR_TypeDef *) LPC_CT16B0_BASE)
#define LPC_TMR16B1 ((LPC_TMR_TypeDef *) LPC_CT16B1_BASE)
#define LPC_TMR32B0 ((LPC_TMR_TypeDef *) LPC_CT32B0_BASE)
#define LPC_TMR32B1 ((LPC_TMR_TypeDef *) LPC_CT32B1_BASE)
#define LPC_IOCON ((LPC_IOCON_TypeDef *) LPC_IOCON_BASE )
#define LPC_SYSCON ((LPC_SYSCON_TypeDef *) LPC_SYSCON_BASE)
#define LPC_GPIO0 ((LPC_GPIO_TypeDef *) LPC_GPIO0_BASE )
#define LPC_GPIO1 ((LPC_GPIO_TypeDef *) LPC_GPIO1_BASE )
#define LPC_GPIO2 ((LPC_GPIO_TypeDef *) LPC_GPIO2_BASE )
#define LPC_GPIO3 ((LPC_GPIO_TypeDef *) LPC_GPIO3_BASE )
.END
Example
Reference: UM10398 LPC11xx Usert Manual 24 September 2012
Chapter 7: LPC1100/LPC1100C/LPC1100L series: I/O configuration (IOCONFIG)
7.3.1 Pin function
The FUNC bits in the IOCON registers can be set to GPIO (FUNC = 000) or to a peripheral function. If the pins are GPIO pins, the GPIOnDIR registers determine whether
the pin is configured as an input or output (see Section 12.3.2).
For any peripheral function, the pin direction is controlled automatically depending on the pin’s functionality.
The GPIOnDIR registers have no effect for peripheral functions.
Table 56. I/O configuration registers ordered by port number
Port pin Register name
PIO0_0 IOCON_RESET_PIO0_0
PIO0_1 IOCON_PIO0_1
PIO0_2 IOCON_PIO0_2
PIO0_3 IOCON_PIO0_3
PIO0_4 IOCON_PIO0_4
PIO0_5 IOCON_PIO0_5
PIO0_6 IOCON_PIO0_6
PIO0_7 IOCON_PIO0_7
PIO0_8 IOCON_PIO0_8
PIO0_9 IOCON_PIO0_9
PIO0_10 IOCON_SWCLK_PIO0_10
PIO0_11 IOCON_R_PIO0_11
PIO1_0 IOCON_R_PIO1_0
PIO1_1 IOCON_R_PIO1_1
PIO1_2 IOCON_R_PIO1_2
PIO1_3 IOCON_SWDIO_PIO1_3
PIO1_4 IOCON_PIO1_4
PIO1_5 IOCON_PIO1_5
PIO1_6 IOCON_PIO1_6
PIO1_7 IOCON_PIO1_7
PIO1_8 IOCON_PIO1_8
PIO1_9 IOCON_PIO1_9
PIO1_10 IOCON_PIO1_10
PIO1_11 IOCON_PIO1_11
PIO2_0 IOCON_PIO2_0
PIO2_1 IOCON_PIO2_1
PIO2_2 IOCON_PIO2_2
PIO2_3 IOCON_PIO2_3
PIO2_4 IOCON_PIO2_4
PIO2_5 IOCON_PIO2_5
PIO2_6 IOCON_PIO2_6
PIO2_7 IOCON_PIO2_7
PIO2_8 IOCON_PIO2_8
PIO2_9 IOCON_PIO2_9
PIO2_10 IOCON_PIO2_10
PIO2_11 IOCON_PIO2_11
PIO3_0 IOCON_PIO3_0
PIO3_1 IOCON_PIO3_1
PIO3_2 IOCON_PIO3_2
PIO3_3 IOCON_PIO3_3
PIO3_4 IOCON_PIO3_4
PIO3_5 IOCON_PIO3_5
- IOCON_SCK_LOC
- IOCON_DSR_LOC
- IOCON_DCD_LOC
- IOCON_RI_LOC
7.4.4 IOCON_PIO0_1
2:0 FUNC Selects pin function. All other values are reserved. 000
0x0 Selects function PIO0_1.
0x1 Selects function CLKOUT.
0x2 Selects function CT32B0_MAT2.
4:3 MODE Selects function mode (on-chip pull-up/pull-down resistor control). 10
0x0 Inactive (no pull-down/pull-up resistor enabled).
0x1 Pull-down resistor enabled.
0x2 Pull-up resistor enabled.
0x3 Repeater mode.
*** Example - Blink Xia Board LEDs ***
*** Xia Board LEDs ***
ledPortPinArrayArray XiaLedPortPinArrayArray = {{Port1, Pin8}, {Port2, Pin7}, {Port2, Pin8}, {Port2, Pin5}};
*** GPIO port setting ***
Ref: UM10398
Table 61. IOCON_PIO1_8 register (IOCON_PIO1_8, address 0x4004 4014)
2:0 FUNC Selects pin function. All other values are reserved. 000
0x0 Selects function PIO1_8.
0x1 Selects function CT16B1_CAP0.
4:3 MODE Selects function mode (on-chip pull-up/pull-down resistor control). 10
0x0 Inactive (no pull-down/pull-up resistor enabled).
0x1 Pull-down resistor enabled.
0x2 Pull-up resistor enabled.
0x3 Repeater mode.
Table 63. IOCON_PIO2_7 register (IOCON_PIO2_7, address 0x4004 4020)
2:0 FUNC Selects pin function. All other values are reserved. 000
0x0 Selects function PIO2_7.
4:3 MODE Selects function mode (on-chip pull-up/pull-down resistor control).
0x0 Inactive (no pull-down/pull-up resistor enabled).
0x1 Pull-down resistor enabled.
0x2 Pull-up resistor enabled.
0x3 Repeater mode.
Table 64. IOCON_PIO2_8 register (IOCON_PIO2_8, address 0x4004 4024)
2:0 FUNC Selects pin function. All other values are reserved. 000
0x0 Selects function PIO2_8.
4:3 MODE Selects function mode (on-chip pull-up/pull-down resistor control).
0x0 Inactive (no pull-down/pull-up resistor enabled).
0x1 Pull-down resistor enabled.
0x2 Pull-up resistor enabled.
0x3 Repeater mode.
Table 72. IOCON_PIO2_5 register (IOCON_PIO2_5, address 0x4004 4044)
2:0 FUNC Selects pin function. All other values are reserved.
0x0 Selects function PIO2_5.
4:3 MODE Selects function mode (on-chip pull-up/pull-down resistor control).
0x0 Inactive (no pull-down/pull-up resistor enabled).
0x1 Pull-down resistor enabled.
0x2 Pull-up resistor enabled.
0x3 Repeater mode.
7.4.23 IOCON_PIO0_8
Table 79. IOCON_PIO0_8 register (IOCON_PIO0_8, address 0x4004 4060)
bit description
Bit Symbol Value Description Reset value
2:0 FUNC Selects pin function. All other values are reserved. 000
0x0 Selects function PIO0_8.
0x1 Selects function MISO0.
0x2 Selects function CT16B0_MAT0.
4:3 MODE Selects function mode (on-chip pull-up/pull-down resistor control). 10
0x0 Inactive (no pull-down/pull-up resistor enabled).
0x1 Pull-down resistor enabled.
0x2 Pull-up resistor enabled.
0x3 Repeater mode.
5 HYS Hysteresis.
0 Disable.
1 Enable.
9:6 - - Reserved
10 OD Selects pseudo open-drain mode. See Section 7.1 for part specific details.
0 Standard GPIO output
1 Open-drain output
31:11 - - Reserved
7.4.4 IOCON_PIO0_1
Table 60. IOCON_PIO0_1 register (IOCON_PIO0_1, address 0x4004 4010)
2:0 FUNC Selects pin function. All other values are reserved. 000
0x0 Selects function PIO0_1.
0x1 Selects function CLKOUT.
0x2 Selects function CT32B0_MAT2.
4:3 MODE Selects function mode (on-chip pull-up/pull-down resistor control). 10
0x0 Inactive (no pull-down/pull-up resistor enabled).
0x1 Pull-down resistor enabled.
0x2 Pull-up resistor enabled.
0x3 Repeater mode.
5 HYS Hysteresis. 0
0 Disable.
1 Enable.
9:6 - - Reserved 0011
10 OD Selects pseudo open-drain mode. See Section 7.1 for part specific details. 0
0 Standard GPIO output
1 Open-drain output
31:11 - - Reserved -
*** Timer Example 1 ***
LPC_SYSCON ->SYSAHBCLKCTRL |= (1 << 8); // Enable Clock for TMR1
LPC_IOCON ->PIO1_9 |= (1 << 0); // PIN1_9 = CT16B1_MAT0
LPC_TMR16B1 ->MR0 = 2000; // 50% Duty Cycle
LPC_TMR16B1 ->PR = 12000;
LPC_TMR16B1 ->MR3 = 4000; // Cycle Length
LPC_TMR16B1 ->MCR |= (1 << 10); // TC Reset on MR3 Match
LPC_TMR16B1 ->PWMC |= (1 << 0); // PWM Mode
LPC_TMR16B1 ->TCR |= (1 << 0); // GO
Timer Example 2
// LPC_IOCON->PIO0_8
// I/O configuration for pin PIO0_8/MISO0/CT16B0_MAT0 (R/W)
struct _PIO0_8
{
uint32_t FUNC : 3; // pin function
uint32_t MODE : 2; // pull up/down resistor mode
uint32_t HYS : 1; // Hysteresis.
uint32_t reserved0 : 4;
uint32_t OD : 1; // Selects pseudo open-drain mode
uint32_t reserved1 : 21;
};
Use inline functions to cast the ptr to register to the structure and then set/get the bit field values.
#define PIO0_8_FUNC_GPIO 0x0
#define PIO0_8_FUNC_MISO 0x1
#define PIO0_8_FUNC_TIMER 0x2
inline void IOCON_PIO0_8_FUNC(uint32_t val)
{
((_PIO0_8*)&LPC_IOCON->PIO0_8)->FUNC = val;
}
Let the compiler figure out all of the masks and bit shifts for me.
Here is what programming the 16-bit timer for PWM looks like with these inline functions:
void SetupPWM()
{
// Enables clock for 16-bit counter/timer 0
SYSCON_SYSAHBCLKCTRL_CT16B0(SYSAHBCLKCTRL_ENABLE);
// setup pin 1 for PWM output
IOCON_PIO0_8_FUNC(PIO0_8_FUNC_TIMER);
// disable pullup resistor pin 1
IOCON_PIO0_8_MODE(PIO0_8_MODE_NO_RESISTOR);
// set timer prescaler
TMR16B0_PR_Set(SystemFrequency/10000); // TC = 10Khz
// set match register 3 to reset TC
TMR16B0_MCR_MR3R(MCR_ENABLE);
// set PWM duty cycle
TMR16B0_MR3_Set(100); // 100Hz
// set pulse width
TMR16B0_MR0_Set(0); // 0%
// enable PWM mode on match register 0 (MR0)
TMR16B0_PWMC_PWMEN0(PWMC_ENABLE);
// enable counter
TMR16B0_TCR_CEn(TCR_ENABLE);
// reset timers
//TMR16B0_TCR_CRst(TCR_RESET);
}
*** Systick example 1 ***
uint32_t SystemFrequency;
extern "C" void SystemInit(void)
volatile unsigned long SysTickCnt; // SysTick Counter
// SysTick Interrupt Handler (1ms)
extern "C" void SysTick_Handler(void)
{
SysTickCnt++;
}
void Delay(unsigned long tick)
{
unsigned long systickcnt;
systickcnt = SysTickCnt;
// TODO: handle when SysTickCnt overflows
while ((SysTickCnt - systickcnt) < tick);
}
int main(void)
{
// Set system frequency to 48MHz
SystemFrequency = ConfigurePLL(12000000UL, 48000000UL);
// Enable clock to IO Configuration block. Needed for UART, SPI, I2C, etc...
SYSCON_SYSAHBCLKCTRL_IOCON(SYSAHBCLKCTRL_ENABLE);
SysTick_Config(SystemFrequency/1000 - 1); // Generate interrupt each 1 ms
// set direction on port 0_7 (pin 28) to output
GPIO0_DIR(7, GPIO_OUTPUT);
while (1)
{
int j;
for (j = 0; j < 10; ++j)
{
Delay(50);
GPIO0_DATA(7, 1); // turn on LED on pin 28
Delay(50);
GPIO0_DATA(7, 0); // turn off LED
}
Delay(1000);
}
}
*** NXP Blinky 01/18/2010 v1.0 ***
/* Includes ------------------------------------------------------------------*/
#include "LPC11xx.h" /* LPC11xx definitions */
#include "timer16.h"
#include "clkconfig.h"
#include "gpio.h"
extern volatile uint32_t timer16_0_counter;
extern volatile uint32_t timer16_1_counter;
#define TEST_TIMER_NUM 0 /* 0 or 1 for 16-bit timers only */
int main (void) {
SystemInit();
/* Config CLKOUT, mostly used for debugging. */
CLKOUT_Setup( CLKOUTCLK_SRC_MAIN_CLK );
LPC_IOCON->PIO0_1 &= ~0x07;
LPC_IOCON->PIO0_1 |= 0x01; /* CLK OUT */
/* Enable AHB clock to the GPIO domain. */
LPC_SYSCON->SYSAHBCLKCTRL |= (1<<6);
/* TEST_TIMER_NUM is either 0 or 1 for 16-bit timer 0 or 1. */
init_timer16(TEST_TIMER_NUM, TIME_INTERVAL);
enable_timer16(TEST_TIMER_NUM);
/* Set port 2_0 to output */
GPIOSetDir( 2, 9, 1 );
while (1) /* Loop forever */
{
#if TEST_TIMER_NUM
/* I/O configuration and LED setting pending. */
if ( (timer16_1_counter > 0) && (timer16_1_counter <= 200) )
{
GPIOSetValue( 2, 9, 0 );
}
if ( (timer16_1_counter > 200) && (timer16_1_counter <= 400) )
{
GPIOSetValue( 2, 9, 1 );
}
else if ( timer16_1_counter > 400 )
{
timer16_1_counter = 0;
}
#else
/* I/O configuration and LED setting pending. */
if ( (timer16_0_counter > 0) && (timer16_0_counter <= 200) )
{
GPIOSetValue( 2, 9, 0 );
}
if ( (timer16_0_counter > 200) && (timer16_0_counter <= 400) )
{
GPIOSetValue( 2, 9, 1 );
}
else if ( timer16_0_counter > 400 )
{
timer16_0_counter = 0;
}
#endif
}
}
.END
No comments:
Post a Comment